Roberts-gorden Vantage TF TF-160 Manual do Utilizador

WARNINGFOR YOUR SAFETYIf you smell gas:1. Open windows.2. DO NOT try to light any appliance.3. DO NOT use electrical switches.4. DO NOT use any teleph

TF-SERIES INSTALLATION, OPERATION AND SERVICE MANUAL4 NOTE: 1. All dimensions are from the surfaces of all tubes, couplings and elbows.2. Clearances B

SECTION 3: CRITICAL CONSIDERATIONS 5NOTE: 1. All dimensions are from the surfaces of all tubes, couplings and elbows.2. Clearances B, C and D can be

TF-SERIES INSTALLATION, OPERATION AND SERVICE MANUAL6 NOTE: 1. All dimensions are from the surfaces of all tubes, couplings and elbows.2. Clearances B

SECTION 4: NATIONAL STANDARDS AND APPLICABLE CODES 7SECTION 4: NATIONAL STANDARDS AND APPLICABLE CODES4.1 Gas CodesThe type of gas appearing on the n

TF-SERIES INSTALLATION, OPERATION AND SERVICE MANUAL8 SECTION 5: MAJOR COMPONENTS FIGURE 11: Major Component DescriptionsBurner with Tube GasketMust b

SECTION 5: MAJOR C OMPONENTS 95.1 Standard Parts List*Canadian Models: Rubber (Type 1) Gas Hoses available as an accessory. See Page 40, Section 10.T

TF-SERIES INSTALLATION, OPERATION AND SERVICE MANUAL10 Additional tubing length may be added to heater. Tubing must be heat-treated, aluminized or por

SECTION 6: SUGGESTED L AYOUTS 11SECTION 6: SUGGESTED LAYOUTS The following are suggested layouts for the heater. These layouts are effective in maxim

TF-SERIES INSTALLATION, OPERATION AND SERVICE MANUAL12 6.4 TF-160 - Single Elbow Design (Individual Vents)6.5 TF-160 Double "L" Design (Indi

SECTION 7: HEATER INSTALLATION 13SECTION 7: HEATER INSTALLATIONTo ensure your safety, and comply with the terms of the warranty, all units must be in

TF-SERIES INSTALLATION, OPERATION AND SERVICE MANUAL14 FIGURE 12: Critical Hanger PlacementHangerSide ViewMust Be Within 4" (10 cm) Front ViewS H

SECTION 7: HEATER INSTALLATION 15FIGURE 13: Linear Heater Assembly Overview TurbulatorFlatWasherNut(Tor que 120 in/lb13.56 Nm)Tube ClampBoltReflector

TF-SERIES INSTALLATION, OPERATION AND SERVICE MANUAL16 FIGURE 14: Linear Heater Layout OverviewBurnerReflectorTubeTube/ReflectorHangerCouplingAssembly

SECTION 7: HEATER INSTALLATION 17FIGURE 15: Linear Heater Layout Overview (Continued)cbdee e e e60' (18 m) Tube Length (Each Side)fgbcdee e e e

TF-SERIES INSTALLATION, OPERATION AND SERVICE MANUAL18 Step 7.1 Burner Tube InstallationStep 7.2 Burner Installation7' 6" ± 1'(229 cm ±

SECTION 7: HEATER INSTALLATION 19Step 7.3 Tube Clamp Package InstallationStep 7.4 Coupling and Tube AssemblyBoltFlatWasherTube ClampNut(Torque 120 in

TF-SERIES INSTALLATION, OPERATION AND SERVICE MANUAL20 Step 7.4.1 Coupling and Tube Assembly (Continued)Step 7.4.2 Coupling and Tube Assembly (Continu

SECTION 7: HEATER INSTALLATION 21Step 7.5 Turbulator InstallationStep 7.6 Reflector InstallationTwistPull StringTabFold tab around outsideof tube nea

TF-SERIES INSTALLATION, OPERATION AND SERVICE MANUAL22 Step 7.6.1 Reflector, U-Clip and Reflector Support InstallationThe pictorial drawings of the he

© 2005All rights reserved. No part of this work covered by the copyrights herein may be reproducedor copied in any form or by any means - graphic, ele

TABLE OF FIGURESFigure 1: Standard Reflector ... 3Figure 2: One Side Reflector...

SECTION 1: HEATER SAFETY 1SECTION 1: HEATER SAFETYYour Safety is Important to Us!This symbol is used throughout the manual to notify you of possible

TF-SERIES INSTALLATION, OPERATION AND SERVICE MANUAL2 SECTION 2: INSTALLER RESPONSIBILITYThe installer is responsible for the following:• To install t

SECTION 3: CRITICAL CONSIDERATIONS 3SECTION 3: CRITICAL CONSIDERATIONS3.1 Required Clearances to CombustiblesClearances are the required distances th